Full 25-point door and opener safety check with every visit - springs, cables, rollers, tracks, and your LiftMaster or Chamberlain opener included
You get a price before we start. It does not change when the truck arrives.
Before
After
Before
After
Before
AfterLiftMaster Torsion Spring Replacement: The Arlington Owner’s Guide
LiftMaster-compatible torsion spring replacement in Arlington typically runs $180-$340 installed, and we stock the common sizes on our trucks for same-day completion. Most homeowners discover the failure when the door suddenly feels heavy, won’t stay open halfway, or the opener strains and reverses. In the Texas heat, a standard-cycle spring often gives out after 8-12 years of daily use, sometimes without warning.
Which LiftMaster Models This Applies To
LiftMaster does not manufacture its own torsion springs. The springs on your LiftMaster-equipped door were matched at original installation to the door’s weight and height, not to the opener model. That said, we regularly replace springs on Arlington homes with LiftMaster belt-drive, chain-drive, and wall-mount openers from the Elite, Premium, and Contractor series.
To identify the correct replacement, we measure wire gauge, inside diameter, and overall coil length. The color-coded paint marks on the winding cone help, but they fade in Texas sun. We also check the cycle rating: a standard 10,000-cycle spring lasts roughly 7-10 years with twice-daily use, while a 25,000-cycle high-cycle spring nearly doubles that lifespan. We carry both OEM-equivalent and premium aftermarket springs from IDC and Service Spring, and we match to your door’s actual weight, not just the sticker on the opener.
One compatibility gotcha in Arlington’s older neighborhoods like Interlochen and Pantego: some original 1980s installations used non-standard 1-3/4″ inside diameter springs that are not stocked by big-box retailers. We carry those on the truck.
Signs Your LiftMaster Torsion Spring Replacement Is Failing
- The door feels suddenly heavy. The spring has lost tension and is no longer counterbalancing the door’s weight. Your LiftMaster opener may still lift it, but the motor is doing work it was never designed for, which burns out the drive gear prematurely.
- A loud bang from the garage, then the door won’t open. This is the classic torsion spring break. The sound is unmistakable, like a firecracker. Afterward, the door is dead weight, and the opener will either hum without moving or trip its safety reverse.
- The door opens unevenly or jerks to one side. On dual-spring setups, one spring has failed and the other is carrying the full load. This puts lateral stress on the cables and tracks, and it will bend hardware if left unaddressed.
- A visible gap in the spring coils. A broken torsion spring often separates by several inches. You can see this from inside the garage with the door closed. Do not attempt to open the door; the remaining spring or cables are under dangerous tension.
- The opener strains, reverses, or the lights flash. LiftMaster openers have force-sensing logic. When the spring fails, the motor detects excess load and treats it as an obstruction. Repeated attempts will overheat the motor and strip the nylon gear.
Replacement Cost & What’s Included
| Service | Price Range in Arlington |
|---|---|
| Single torsion spring replacement | $180-$260 |
| Dual spring replacement (both springs) | $280-$340 |
| Spring + cable replacement (recommended if cables show wear) | $310-$490 |
| Spring + roller replacement (if rollers are cracked) | $290-$450 |
What drives the range: door height (8-foot vs. 9-foot), spring cycle rating, whether one or both springs are replaced, and whether related hardware needs attention. We quote the flat price before the wrench comes out. That price includes the spring, labor, winding bar safety work, balance and travel limit adjustment, and a written 90-Day Done Right Promise. We do not start work until you approve the number.
DIY or Call Us?
There is a safe middle ground here. You can verify the symptoms: look for the coil gap, test the door’s weight by disengaging the opener and lifting manually, check if the LiftMaster rail wobbles during operation. These observations help us diagnose over the phone.
What you should not do: unwind a loaded torsion spring with improvised tools. The spring stores enough torque to cause serious hand, face, or head injury. We have seen Arlington homeowners use screwdriver substitutes and wind up in the ER. The winding cones require matched steel winding bars inserted fully and sequentially. This is not a YouTube confidence problem; it is a physics problem.
We carry the right springs, the right bars, and the right training. Call (817) 241-8437 and we will walk through what you are seeing.
FAQs
A standard 10,000-cycle spring lasts 8-12 years with normal use, but Arlington’s temperature swings from 20°F winter lows to 105°F summer highs accelerate metal fatigue. We see more spring failures in August and January than any other months. High-cycle 25,000-spring upgrades add roughly $60-$90 but often double the lifespan. Call (817) 241-8437 for an exact quote on your door.
No. A broken torsion spring cannot be spliced, welded, or re-tensioned to factory spec. Once the coil structure fails, replacement is the only safe option. We have inspected attempted repairs in Arlington that held for days before snapping violently. We replace with new, properly rated springs every time. Call (817) 241-8437 for a free estimate.
Most single-spring replacements take 45-60 minutes from truck arrival to final balance test. Dual-spring setups run 60-90 minutes. We adjust the LiftMaster opener force settings afterward so the motor is not overworking. The door should run quiet and stay put at half-height when we are done. Call (817) 241-8437 to schedule.
We stock torsion springs for the most common Arlington door sizes: 8×7, 9×7, 16×7, and 18×8, in wire sizes from .207 to .283. For odd sizes or high-lift track configurations, we source overnight from our Dallas-Fort Worth supplier. Most jobs are completed in a single visit. Call (817) 241-8437 to confirm we have your size.
Mainspring Garage Door Co. is an independent service provider; we are not affiliated with LiftMaster, though our technicians are factory-familiar with all major brands including LiftMaster, Chamberlain, and Genie. We also service Clopay, Amarr, Wayne Dalton, Craftsman, and Raynor doors and openers.
If your LiftMaster opener is straining, your door feels heavy, or you heard that bang and now nothing moves, call us at (817) 241-8437. A live person answers, day or night. We will quote the work upfront, arrive with the parts, and stand behind it for 90 days in writing. That is the square deal we have offered Arlington since 1984.
Written by Carl Dutton, Owner, Mainspring Garage Door Co. at Mainspring Garage Door Co., serving Arlington and nearby areas.